Product certificate register

HomeRAB™ Pre-Cladding and RAB™ Board by James Hardie are a range of rigid wall underlay products. They are sealed medium density fibre cement sheets

The Firth RibRaft® Floor System is a method of concrete floor construction, suitable for all slab-on-ground concrete floors for domestic or residential buildings that fall within the scope of NZS 3604:2011 Timber framed buildings. 

Trufill Insulation System is a loose-fill blow-in non-bonded granulated glasswool mineral fibre insulation system. It is blown on-site into building cavity spaces to a nominal density of between 12 kg/m3 and 32 kg/m3. When blown in cavities, the insulation is retained by a transparent Blown Insulation Barrier (BIB), over which the internal lining of the building is installed.

Trufill blow-in glasswool Insulation materials shall be Knauf Insulation Supafil Frame or Supafil Carbon plus.

This certificate was suspended by the product certification body on 30th May 2024.

Quick 2 Seal is a two pack, flexible, self-priming waterproofing membrane. Components include:

• Part A (Base) and Part B (Hardener)
• 2-Seal Primer (solvent free two-part etch primer)
• Cohe Group Seam Tape (Butyl rubber self-adhesive tape)
• Cohe Group Geofabric

HBS HEATLOK HFO HIGH-LIFT insulation is a site-applied closed cell, medium density 2-part polyurethane spray-in-place foam thermal insulation product. 

IBS RigidRAP®-XT is a rigid air barrier and bracing element and provides temporary protection from the weather during construction. It contributes thermal resistance to the wall and incorporates a thermal break for use with light steel framing. It is suitable for use on new and existing steel framed or timber framed buildings founded on either a concrete floor slab or timber subfloor. When all joints are sealed with a flashing tape, no flexible wall underlay is required.

IBS RigidRAP® is an 8mm OSB panel product faced with a laminated synthetic building wrap.

Stria™ Cladding is a cavity-based fibre cement panel wall cladding system.

Stria™ Cladding consists of Stria™ Cladding Panel, which is a 14mm profile fibre cement panel, fixed horizontally or vertically over battens to form a nominal 20 mm cavity. Proprietary ventilated timber battens are used in the vertical application. The cladding is finished with a latex paint system.

The cladding system incorporates a primary and secondary means of weather resistance (first and second lines of defence) against water penetration by separating the cladding from the external wall framing with a nominal 20 mm cavity. The cavity allows for any occasional ingress of water that may get past the external skin to drain to the exterior of the building, and any remaining moisture to dry by evaporation.

This certificate was suspended by the product certification body on 5th November 2024.

Moser aluminium clad timber windows and doors are made of solid American white oak timber and aluminium. The external side has a cladding of powder coated aluminium. The solid timber interior has a scratch resistant dual component paint finish. Moser thermal break windows and doors are made of powder coated aluminium. Both the aluminium clad timber and thermal break aluminium windows and doors are double glazed. Window models include fixed window, tilt & turn, awning and hinged casement windows. Door models include inward and outward opening hinged doors and sliding doors.

This certification covers the models listed in Section 9.

Linea™ Weatherboard is a 16 mm thick bevelback fibre cement weatherboard, which is designed to be used as part of an external wall cladding system for residential and light commercial type buildings where domestic construction techniques are used. 

Linea™ Weatherboard Direct Fixed Cladding system consists of Linea™ Weatherboards applied direct to the external wall framing over a flexible underlay. 

Linea™ Weatherboard Cavity Cladding system consists of Linea™ Weatherboards fixed over timber battens to form the cavity. 

Both cladding methods (referenced as the system) incorporate secondary protection behind all internal and external corners, flashings for window, door and meter box penetrations as well as air seals to all wall penetrations.